====== IBM 8265 ATM switch ======
See also:- [[http://www.rainsbrook.co.uk/networking/ibm/8265/index.html]] \\
===== Set ip address on ethernet port =====
Note subnet mask needs to be entered in hex! i.e. 255.255.255.0 == ff.ff.ff.00
ibm8265_01# set device ip_address eth 192.168.1.27 ff.ff.ff.00
IP address and mask set
ibm8265_01# set device default_gateway 192.168.1.1
Default gateway set
ibm8265_01#
Reboot is not needed, access to telnet will now work. Note, ssh is not supported.
$ telnet ibm8265-01
Trying 192.168.1.27...
Connected to ibm8265-01.
Escape character is '^]'.
ATM ControlPoint Switch Telnet server at address 192.168.1.27.
Press Enter
8265 ATM Control Point and Switch Module
(C) Copyright IBM Corp. 1997, 1999. All rights reserved.
Password:
Welcome to system administrator service on ibm8265_01.
ibm8265_01#
===== See what is installed =====
ibm8265_01# show module all
Slot Install Connect Operation General Information
-------------------------------------------------------------------------------
1 Y Y Y 8265 ATM MSS Server Module
2 n n n -
3 Y Y Y 8265 ATM 12 ports 25 Mbps Module
4 n n n -
5 Y Y Y 8265 ATM WAN Module with E1 + E1 Ports
6 n p n -
7 n p n -
8 n n n -
9 Y Y Y 8265 ATM Control Point and Switch Module:Active
10 Y n n < Extension >
11 n p n -
12 n n n -
13 Y n n 8265 ATM 4 ports 155 Mbps Module
14 n n n -
15 Y Y Y 8265 ATM 4 ports 155 Mbps Module
16 n p n -
17 Y Y Y 8265 ATM 4 ports 155 Mbps Module
18 Y n Y Active Controller Module
19 n n n -
ibm8265_01#
Module 13 is disabled, let's enable and disable it (connected and isolated in IBM speak):-
ibm8265_01# set module 13 connected
Slot 13:Module set
ibm8265_01#
ibm8265_01# set module 13 isolated
Slot 13:Module set
ibm8265_01#
Isolated means it can be swapped whilst the chassis is powered on. Slots 1 - 17 are for network modules, slots 18 & 19 are for power control modules. Note that slots 9 & 10 HAVE to be used for the CPSW module in single fabric mode, if a redundant CPSW module is fitted, it has to go in slots 11 & 12.
===== Show port status =====
Port 17.1 is connected to a Fore / Marconi PCA200e 155MB/s pci card on a computer running Centos 6.5, seen below, atmsigd has been started but not ilmid, in the second example, ilmid has been started.
ibm8265_01# show port 17.1 verbose
Type Mode Status
-------------------------------------------------------------------------------
17.01: UNI enabled DOWN:Establishing
UNI Type : Private
Signalling Version : Auto
ILMI status : DOWN:Establishing
ILMI vci : 0.16
RB Bandwidth : unlimited
Police admin. : on
Signalling vci : 0.5
RB Admin weight : 5040
NRB Admin weight : 5040
VPI range admin. : 0-15 (4 bits)
VCI range admin. : 0-1023 (10 bits)
Connector : SC DUPLEX
Media : multimode fiber
Port speed : 155000 kbps
Connection shaping : Off.
Remote device is active
Frame format : SONET STS-3c
Scrambling mode : frame and cell
Clock mode : internal
ibm8265_01#
ibm8265_01# show port 17.1 verbose
Type Mode Status
-------------------------------------------------------------------------------
17.01: UNI enabled UP
UNI Type : Private
Signalling Version : Auto
> Oper Sig. Version : 3.0
ILMI status : UP
ILMI vci : 0.16
RB Bandwidth : unlimited
...edited....
Remote device is active
Frame format : SONET STS-3c
Scrambling mode : frame and cell
Clock mode : internal
ibm8265_01#
===== Saving Configuration =====
Changes are activated immediately they are made, but are not saved to nv ram so will be lost on a device reload. There are several save options, but save all does the lot in one go.
ibm8265_01# save all
ibm8265_01#
===== Links to investigate =====
==== ip over pvc ====
https://os.inf.tu-dresden.de/pca200e/pca200e-linux.archive/msg00087.html \\
http://margo.student.utwente.nl/simon/finished/thesis/thesis2/node43.html \\
http://www.linuxjournal.com/article/3005?page=0,2 \\
==== LANE ====