Differences

This shows you the differences between two versions of the page.

--- networking:fvcaccessngi [02/09/2025 22:04] – andrew
+++ networking:fvcaccessngi [03/09/2025 08:36] (current) – [AccessNGI Configuration] andrew
@@ Line 32: / Line 32: @@
 ADMIN FVCcoreATM>
+ADMIN FVCcoreATM>set telnet passwd yourpassword
+Telnet password changed to: yourpassword
 </code>
-Have a look at the system ports (really for interest only)
+===== Initial view of system =====
+Have a look at the system modules installed and then the ports:-
+<code>
+ADMIN FVCcoreATM>show system
+crash    modules  ports    uptime   version
+ADMIN FVCcoreATM>show system modules
+Module       Revision   Description
+-----------------------------------
+           3      6 x ATM 25Mps module (SALI)
+           1      4 x E1 IMA Module (RJ-48)
+           1      2 x 155Mbps OC3 module (TI)
+                  Not Present
+           0      ETM management module (Strong ARM)
+                  Not Present
+                  Not Present
+                  Not Present
+                  Not Present
+                  Not Present
+Flash Card            slot 3 size 4M
+ADMIN FVCcoreATM>
+</code>
 <code>
@@ Line 59: / Line 84: @@
 </code>
+==== Config of global ATM parameters ====
 Delete the previous config and return to factory defaults
   "set system delflashcfg".
@@ Line 66: / Line 96: @@
 set the atm network prefix length.
-  "set pnni pglevel 96"
+<code>
+ADMIN FVCcoreATM>set pnni pglevel 96
+ADMIN FVCcoreATM>show pnni addrtable
+ADDR: 39826f3148000000000001000a00000000000000 LEN:   104 SCOPE:   0
+ADDR: 39826f3148000000000001002000000000000000 LEN:   104 SCOPE:  96
+ADDR: 39826f3148000000000001002000a0b1007cc200 LEN:   104 SCOPE:   0
+ADMIN FVCcoreATM>
+</code>
 Set the atm network prefix and switch number (Don't use my numbers, they have to match the existing atm numbering hierachy in use). Depending on your atm network mask (pglevel in FVC speak), your ilmi netprefix may be longer or shorter than this. The .05 at the end is the switch id.
@@ Line 77: / Line 117: @@
 This completes the basic global config.
+==== Interfaces ====
 Next start to configure some interfaces:-
@@ Line 87: / Line 129: @@
         "set e1 clocking 201 external"
-Scrambling is only required for e1 ports, not 155MB/s fibre ports.
+Scrambling is only required for e1 ports, not 155MB/s fibre ports. [[hdb3|HDB3 - High Density Bipolar Order 3 Encoding]]
 Please note, the scrambling is to ensure a zero dc average level, not for encryption, security etc....
 HDB3 is "High Density Bipolar 3zero substitution", an alternative to AMI etc. This has to match the line encoding being used by the circuit provider.
-Note also that the pnni implementation includes ilmi, so do NOT enable ilmi for the port. Pnni takes care of it.
+Note also that the PNNI implementation includes ILMI, so do NOT enable ILMI for the port. PNNI takes care of it.
 Next configure the ethernet port to use bridging and connect to ELAN name desired