Rainsbrook

User Tools

Site Tools

Trace:
networking:cisco-2801-gsm-gps

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
networking:cisco-2801-gsm-gps [25/02/2026 14:08] – [VOIP] andrewnetworking:cisco-2801-gsm-gps [30/04/2026 15:09] (current) – created andrew
Line 1: Line 1:
-====== Cisco 2801 with WiFi and gsm / gps modules ====== +Moved to [[cisco-2801-cme|Cisco 2801 with WiFi and Call Manager Express (CME)]]
- +
- +
-===== Boot Failure ===== +
- +
- +
-rommon1> +
- +
-<code> +
-Set the configuration register with the confreg command if the router is in ROMmon mode: +
- +
-rommon 1 > confreg 0x2102 +
- +
-</code> +
- +
-<code> +
-Router#show hardware  +
-Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 15.1(4)M1, RELEASE SOFTWARE (fc1) +
- +
-...edited... +
- +
-ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) +
- +
-Router uptime is 33 minutes +
-System returned to ROM by power-on +
-System restarted at 11:59:32 UTC Mon Jan 2 2006 +
-System image file is "flash:c2801-advipservicesk9-mz.151-4.M1.bin" +
-Last reload type: Normal Reload +
- +
-...edited... +
- +
-Cisco 2801 (revision 7.0) with 358400K/34816K bytes of memory. +
-Processor board ID FCZ121715KL +
-6 FastEthernet interfaces +
-2 Channelized E1/PRI ports +
-1 Virtual Private Network (VPN) Module +
-2 802.11 Radios +
-DRAM configuration is 64 bits wide with parity disabled. +
-191K bytes of NVRAM. +
-125184K bytes of ATA CompactFlash (Read/Write) +
- +
-Configuration register is 0x2102 +
- +
-Router# +
- +
-</code> +
- +
-<code> +
-Router#configure terminal  +
-Enter configuration commands, one per line. End with CNTL/Z. +
-Router(config)#config-register 0x2102 +
-Router(config)#end +
-</code> +
- +
-<code> +
-! +
-boot-start-marker +
-boot system flash:c2801-advipservicesk9-mz.151-4.M1.bin +
-boot-end-marker +
-! +
-</code> +
- +
- +
- +
- +
- +
-===== GSM ===== +
- +
- +
-Using gsm/gps module as a fpga:- [[https://hackaday.io/project/168542-cisco-hwic-3g-cdma-as-a-cheap-fpga-board/log/171121-reverse-engineering-the-cisco-hwic-3g-cdma]] +
- +
- +
-backup cellular routing +
- +
-[[http://wiki.ciscolinux.co.uk/index.php?title=Cisco_1941_with_EHWIC-3G-HSPA%2B7_card_configuration]] +
- +
-[[https://bayupw.blogspot.com/2008/05/configuring-cisco-hwic-3g.html]] +
- +
-[[https://smartvision.solutions/?q=node/25]] +
- +
-{{:networking:ehwic-gsm.png?400|}} +
- +
- +
- +
- +
-==== Create APN profile ==== +
- +
-This is for UK Orange / EE:- +
-<code> +
-Router#$0/0 gsm profile create 3 everywhere chap eesecure secure ipv4         +
-Profile 3 will be created with the following values: +
-PDP type = IPv4 +
-APN = everywhere +
-Authentication = CHAP +
-Username = eesecure +
-Password = secure +
-Are you sure? [confirm] +
-Profile 3 written to modem +
-Router# +
-</code> +
- +
- +
-<code> +
-Router#show cellular 0/0/0 network  +
-Current Service Status = Emergency Only, Service Error = None +
-Current Service = Invalid +
-Packet Service = None +
-Packet Session Status = Inactive +
-Current Roaming Status = Home +
-Network Selection Mode = Automatic +
-Country = GBR, Network = O2 - UK +
-Mobile Country Code (MCC) = 234 +
-Mobile Network Code (MNC) = 10 +
-Location Area Code (LAC) = 21565 +
-Routing Area Code (RAC) = 146 +
-Cell ID = 26948 +
-Primary Scrambling Code = 0 +
-PLMN Selection = Automatic +
-Router# +
- +
-Router#sh cellular 0/0/0 gps detail  +
- +
-GPS Info +
-------------- +
-GPS Status: GPS acquiring +
-GPS Mode Configured: standalone +
-Latitude: 0 Deg 0 Min 0 Sec North +
-Longitude: 0 Deg 0 Min 0 Sec East +
-Timestamp (GMT): Sun Jan  6 00:00:00 1980 +
- +
-Fix type index: 0 +
-HEPE: 0 cm, GPS Mode Used: not configured/unknown, Positioning Source index invalid: 0 +
-Uncertainty Info: +
-  Angle: 0 deg, A: 50 cm, Position: 50 cm, Vertical: 50 cm +
-Satellite Info +
----------------- +
-Router# +
-</code> +
- +
- +
-Need to fix +
-<code> +
-No physical hardware support for line 8 +
- modem InOut +
-      ^ +
-% Invalid input detected at '^' marker. +
- +
- no exec +
-      ^ +
-% Invalid input detected at '^' marker. +
- +
- transport input all +
-      ^ +
-% Invalid input detected at '^' marker. +
- +
- transport output all +
-      ^ +
-% Invalid input detected at '^' marker. +
- +
- stopbits 1 +
-   ^ +
-% Invalid input detected at '^' marker. +
- +
- speed 4800 +
-   ^ +
-% Invalid input detected at '^' marker. +
-</code> +
- +
- +
- +
-====== Cisco 3g hwic gps ====== +
- +
- +
-<del>https://routing-bits.com/2010/05/12/hwic-3g-gsm/</del> Link seems broken. +
- +
-[[https://smartvision.solutions/?q=node/25]] +
- +
- +
-====== Cisco HWIC-AP ====== +
- +
-{{:undefined:hwic-ap.png?200|}} +
-Access point for wifi - UNTESTED! +
- +
-[[https://community.cisco.com/t5/wireless/wireless-config-on-2811-with-hwic-access-point/td-p/648658]] - Broadcast of ssid link +
- +
-<code> +
-! 1. Configure the VLAN for wireless traffic +
-interface Vlan10 +
- ip address 192.168.10.1 255.255.255.0 +
- no shutdown +
- +
-! 2. Configure the Radio Interface (Module/Slot/Port - usually 0/3/0 or 0/2/0) +
-interface Dot11Radio0/3/0 +
- no ip address +
- ! Set channel and power +
- station-role root +
- no shutdown +
- ! +
- ! 3. Define the SSID +
- ssid MyCompanyWireless +
-   authentication open +
-   authentication key-management wpa version 2 +
-   wpa-psk ascii 0 SecretPassword123 +
-   guest-mode +
- ! +
- ! 4. Bridge the radio to the VLAN +
- bridge-group 10 +
- bridge-group 10 subscriber-loop-control +
- bridge-group 10 block-unknown-source +
- no bridge-group 10 source-learning +
- no bridge-group 10 unicast-flooding +
- +
-! 5. Configure the Bridge Virtual Interface (BVI) +
-interface BVI10 +
- ip address 192.168.10.2 255.255.255.0 +
- no shutdown +
- +
-! 6. (Optional) Configure DHCP for clients on this subnet +
-ip dhcp pool WLAN_CLIENTS +
- network 192.168.10.0 255.255.255.0 +
- default-router 192.168.10.1 +
- dns-server 8.8.8.8 +
- +
-</code> +
- +
- +
- +
- +
-====== VOIP ====== +
- +
-[[https://www.mattmillman.com/info/a-crash-course-in-using-gpo-telephones-in-the-modern-world/|Using Analogue BT phones in DTMF]] +
- +
-<code> +
-Router(config)#telephony-service setup +
-Warning: <telephony-service setup> command has been deprecated. +
-For installation help, please check CME System Administrator Guide. +
-Goodbye! +
-Router(config)# +
-</code> +
- +
-<code> +
-Router#show voice port summary  +
-                                           IN       OUT +
-PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC +
-=============== == ============ ===== ==== ======== ======== == +
-0/2/0           --  fxs-ls      up    dorm on-hook  idle     y  +
-0/2/1           --  fxs-ls      up    dorm on-hook  idle     y  +
- +
-</code> +
- +
- +
-<code> +
-Router(config)#voice-port 0/2/0 +
-Router(config-voiceport)#signal ? +
-  groundStart  Ground Start +
-  loopStart    Loop Start +
- +
-Router(config-voiceport)#signal loopStart  +
-Router(config-voiceport)#ring cadence uk? +
-% Unrecognized command +
-Router(config-voiceport)#ring cadence ?  +
-  define     User Defined Cadence +
-  external   External ringing cadence on/off durations (STCAPP only) +
-  pattern01  2sec on 4sec off +
-  pattern02  1sec on 4sec off +
-  pattern03  1.5sec on 3.5sec off +
-  pattern04  1sec on 2sec off +
-  pattern05  1sec on 5sec off +
-  pattern06  1sec on 3sec off +
-  pattern07  .8sec on 3.2sec off +
-  pattern08  1.5sec on 3sec off +
-  pattern09  1.2sec on 3.7sec off +
-  pattern10  1.2sec on 4.7sec off +
-  pattern11  .4sec on .2sec off .4sec on 2sec off +
-  pattern12  .4sec on .2sec off .4sec on 2.6sec off +
- +
-Router(config-voiceport)#ring cadence pattern11 +
-Router(config-voiceport)#exit +
- +
- +
-</code> +
- +
- +
-Running config to call between FXS ports +
- +
-<code> +
-voice-port 0/2/0 +
- ring cadence pattern11 +
- station-id name analogue1 +
- station-id number 1001 +
-! +
-voice-port 0/2/1 +
- ring cadence pattern11 +
- station-id name analogue2 +
- station-id number 1002 +
-! +
-! +
-! +
-mgcp profile default +
-! +
-! +
-dial-peer voice 1001 pots +
- destination-pattern 1001 +
- port 0/2/0 +
-! +
-dial-peer voice 1002 pots +
- destination-pattern 1002 +
- port 0/2/1 +
-! +
-</code> +
- +
- +
- +
-====== 7911G ====== +
- +
-Complete dump of info.. don't believe anything here, not tested. +
- +
-<code> +
-voice register global +
- mode cme +
- load 7911 SCCP11.8-4-4S  ! Ensure this matches your firmware file +
- tftp-path flash: +
- max-dn 10 +
- max-pool 10 +
- source-address <192.168.x.x> port 2000 +
- ! +
-voice register pool 1 +
- id mac <AAAA.BBBB.CCCC>  ! Phone MAC Address +
- type 7911 +
- number 1 dn 1 +
- username <username> password <password> +
- codec g711ulaw +
- ! +
-voice register dn 1 +
- number 101 ! Extension number +
- +
-</code> +
- +
- +
- +
-====== VIC2-2FXS ====== +
- +
-Two ports of analogue in a VIC cards, 2x RJ-11 sockets +
- +
-{{:undefined:vic2-2fxs.png?200|}} +
- +
- +
- +
-See [[https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/99946-cme-sip-guide.html]] for sccp config. +
  
networking/cisco-2801-gsm-gps.1772028493.txt.gz · Last modified: by andrew
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki