Differences

This shows you the differences between two versions of the page.

--- networking:cisco-2801-gsm-gps [17/02/2026 15:14] – andrew
+++ networking:cisco-2801-gsm-gps [02/03/2026 13:03] (current) – removed andrew
@@ Line 1: / Line 1: @@
-====== Cisco 2801 with WiFi and gsm / gps modules ======
-===== Boot Failure =====
-rommon1>
-<code>
-Set the configuration register with the confreg command if the router is in ROMmon mode:
-rommon 1 > confreg 0x2102
-</code>
-<code>
-Router#show hardware
-Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 15.1(4)M1, RELEASE SOFTWARE (fc1)
-...edited...
-ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
-Router uptime is 33 minutes
-System returned to ROM by power-on
-System restarted at 11:59:32 UTC Mon Jan 2 2006
-System image file is "flash:c2801-advipservicesk9-mz.151-4.M1.bin"
-Last reload type: Normal Reload
-...edited...
-Cisco 2801 (revision 7.0) with 358400K/34816K bytes of memory.
-Processor board ID FCZ121715KL
-FastEthernet interfaces
-Channelized E1/PRI ports
-Virtual Private Network (VPN) Module
-802.11 Radios
-DRAM configuration is 64 bits wide with parity disabled.
-K bytes of NVRAM.
-K bytes of ATA CompactFlash (Read/Write)
-Configuration register is 0x2102
-Router#
-</code>
-<code>
-Router#configure terminal
-Enter configuration commands, one per line. End with CNTL/Z.
-Router(config)#config-register 0x2102
-Router(config)#end
-</code>
-<code>
-!
-boot-start-marker
-boot system flash:c2801-advipservicesk9-mz.151-4.M1.bin
-boot-end-marker
-!
-</code>
-===== GSM =====
-Using gsm/gps module as a fpga:- [[https://hackaday.io/project/168542-cisco-hwic-3g-cdma-as-a-cheap-fpga-board/log/171121-reverse-engineering-the-cisco-hwic-3g-cdma]]
-backup cellular routing
-[[http://wiki.ciscolinux.co.uk/index.php?title=Cisco_1941_with_EHWIC-3G-HSPA%2B7_card_configuration]]
-[[https://bayupw.blogspot.com/2008/05/configuring-cisco-hwic-3g.html]]
-{{:networking:ehwic-gsm.png?400|}}
-==== Create APN profile ====
-This is for UK Orange / EE:-
-<code>
-Router#$0/0 gsm profile create 3 everywhere chap eesecure secure ipv4
-Profile 3 will be created with the following values:
-PDP type = IPv4
-APN = everywhere
-Authentication = CHAP
-Username = eesecure
-Password = secure
-Are you sure? [confirm]
-Profile 3 written to modem
-Router#
-</code>
-<code>
-Router#show cellular 0/0/0 network
-Current Service Status = Emergency Only, Service Error = None
-Current Service = Invalid
-Packet Service = None
-Packet Session Status = Inactive
-Current Roaming Status = Home
-Network Selection Mode = Automatic
-Country = GBR, Network = O2 - UK
-Mobile Country Code (MCC) = 234
-Mobile Network Code (MNC) = 10
-Location Area Code (LAC) = 21565
-Routing Area Code (RAC) = 146
-Cell ID = 26948
-Primary Scrambling Code = 0
-PLMN Selection = Automatic
-Router#
-Router#sh cellular 0/0/0 gps detail
-GPS Info
--------------
-GPS Status: GPS acquiring
-GPS Mode Configured: standalone
-Latitude: 0 Deg 0 Min 0 Sec North
-Longitude: 0 Deg 0 Min 0 Sec East
-Timestamp (GMT): Sun Jan  6 00:00:00 1980
-Fix type index: 0
-HEPE: 0 cm, GPS Mode Used: not configured/unknown, Positioning Source index invalid: 0
-Uncertainty Info:
-  Angle: 0 deg, A: 50 cm, Position: 50 cm, Vertical: 50 cm
-Satellite Info
-----------------
-Router#
-</code>
-Need to fix
-<code>
-No physical hardware support for line 8
- modem InOut
-      ^
-% Invalid input detected at '^' marker.
- no exec
-      ^
-% Invalid input detected at '^' marker.
- transport input all
-      ^
-% Invalid input detected at '^' marker.
- transport output all
-      ^
-% Invalid input detected at '^' marker.
- stopbits 1
-   ^
-% Invalid input detected at '^' marker.
- speed 4800
-   ^
-% Invalid input detected at '^' marker.
-</code>
-====== Cisco 3g hwic gps ======
-<del>https://routing-bits.com/2010/05/12/hwic-3g-gsm/</del> Link seems broken.
-[[https://smartvision.solutions/?q=node/25]]
-====== Cisco HWIC-AP ======
-{{:undefined:hwic-ap.png?200|}}
-Access point for wifi - UNTESTED!
-[[https://community.cisco.com/t5/wireless/wireless-config-on-2811-with-hwic-access-point/td-p/648658]] - Broadcast of ssid link
-<code>
-! 1. Configure the VLAN for wireless traffic
-interface Vlan10
- ip address 192.168.10.1 255.255.255.0
- no shutdown
-! 2. Configure the Radio Interface (Module/Slot/Port - usually 0/3/0 or 0/2/0)
-interface Dot11Radio0/3/0
- no ip address
- ! Set channel and power
- station-role root
- no shutdown
- !
- ! 3. Define the SSID
- ssid MyCompanyWireless
-   authentication open
-   authentication key-management wpa version 2
-   wpa-psk ascii 0 SecretPassword123
-   guest-mode
- !
- ! 4. Bridge the radio to the VLAN
- bridge-group 10
- bridge-group 10 subscriber-loop-control
- bridge-group 10 block-unknown-source
- no bridge-group 10 source-learning
- no bridge-group 10 unicast-flooding
-! 5. Configure the Bridge Virtual Interface (BVI)
-interface BVI10
- ip address 192.168.10.2 255.255.255.0
- no shutdown
-! 6. (Optional) Configure DHCP for clients on this subnet
-ip dhcp pool WLAN_CLIENTS
- network 192.168.10.0 255.255.255.0
- default-router 192.168.10.1
- dns-server 8.8.8.8
-</code>
-====== VOIP ======
-[[https://www.mattmillman.com/info/a-crash-course-in-using-gpo-telephones-in-the-modern-world/|Using Analogue BT phones in DTMF]]
-<code>
-Router(config)#telephony-service setup
-Warning: <telephony-service setup> command has been deprecated.
-For installation help, please check CME System Administrator Guide.
-Goodbye!
-Router(config)#
-</code>
-<code>
-Router#show voice port summary
-                                           IN       OUT
-PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
-=============== == ============ ===== ==== ======== ======== ==
-/2/0           --  fxs-ls      up    dorm on-hook  idle     y
-/2/1           --  fxs-ls      up    dorm on-hook  idle     y
-</code>
-<code>
-Router(config)#voice-port 0/2/0
-Router(config-voiceport)#signal ?
-  groundStart  Ground Start
-  loopStart    Loop Start
-Router(config-voiceport)#signal loopStart
-Router(config-voiceport)#ring cadence uk?
-% Unrecognized command
-Router(config-voiceport)#ring cadence ?
-  define     User Defined Cadence
-  external   External ringing cadence on/off durations (STCAPP only)
-  pattern01  2sec on 4sec off
-  pattern02  1sec on 4sec off
-  pattern03  1.5sec on 3.5sec off
-  pattern04  1sec on 2sec off
-  pattern05  1sec on 5sec off
-  pattern06  1sec on 3sec off
-  pattern07  .8sec on 3.2sec off
-  pattern08  1.5sec on 3sec off
-  pattern09  1.2sec on 3.7sec off
-  pattern10  1.2sec on 4.7sec off
-  pattern11  .4sec on .2sec off .4sec on 2sec off
-  pattern12  .4sec on .2sec off .4sec on 2.6sec off
-Router(config-voiceport)#ring cadence pattern11
-Router(config-voiceport)#exit
-</code>
-Running config to call between FXS ports
-<code>
-voice-port 0/2/0
- ring cadence pattern11
- station-id name analogue1
- station-id number 1001
-!
-voice-port 0/2/1
- ring cadence pattern11
- station-id name analogue2
- station-id number 1002
-!
-!
-!
-mgcp profile default
-!
-!
-dial-peer voice 1001 pots
- destination-pattern 1001
- port 0/2/0
-!
-dial-peer voice 1002 pots
- destination-pattern 1002
- port 0/2/1
-!
-</code>
-====== VIC2-2FXS ======
-Two ports of analogue in a VIC cards, 2x RJ-11 sockets
-See [[https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/99946-cme-sip-guide.html]] for sccp config.