Differences

This shows you the differences between two versions of the page.

--- networking:cisco-2801-cme [14/04/2026 16:15] – andrew
+++ networking:cisco-2801-cme [23/04/2026 23:33] (current) – [Cisco HWIC-AP] andrew
@@ Line 5: / Line 5: @@
-rommon1>
+System boots to ''rommon1>'' but no further.
 <code>
-Set the configuration register with the confreg command if the router is in ROMmon mode:
+Set the configuration register with the confreg command if the router is in rommon mode:
 rommon 1 > confreg 0x2102
 </code>
+Boot ok, so let's see what's detected.
 <code>
@@ Line 45: / Line 47: @@
 </code>
+Set the config register in IOS:-
 <code>
@@ Line 52: / Line 57: @@
 Router(config)#end
 </code>
+From a ''dir flash:'', get the IOS file name to boot from:-
 <code>
@@ Line 60: / Line 67: @@
 !
 </code>
@@ Line 70: / Line 72: @@
 ====== Cisco HWIC-AP ======
-{{:undefined:hwic-ap.png?200|}}
+{{:undefined:hwic-ap.png?300|}}
-Access point for wifi - UNTESTED!
+Access point for wifi - very sketchy so far.
 [[https://community.cisco.com/t5/wireless/wireless-config-on-2811-with-hwic-access-point/td-p/648658]] - Broadcast of ssid link
@@ Line 121: / Line 124: @@
 [[https://www.mattmillman.com/info/a-crash-course-in-using-gpo-telephones-in-the-modern-world/|Using Analogue BT phones in DTMF]]
+[[https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/manual/cmeadm/cmebasic.html]]
+[[https://binaryfury.wann.net/2025/05/quest-for-network-side-isdn-on-cisco-router/]]
+===== DHCP service =====
+If your router is required to offer DHCP, use this:-
+<code>
+ip dhcp excluded-address 192.168.101.1 192.168.101.50
+ip dhcp pool voip
+ network 192.168.101.0 255.255.255.0
+ default-router 192.168.101.1
+ dns-server 192.168.101.1
+ domain-name voip.rainsbrook.co.uk
+!
+</code>
+To see leases offered out, don't use this:-
+<code>
+-1#sh dhcp ?
+  lease   Show DHCP Addresses leased from a server
+  server  Show DHCP Servers we know about
+-1#
+</code>
+This is to see leases offered **TO** the router, not **from** it.
+Use this instead:-
+<code>
+-1#sh ip dhcp ?
+  binding   DHCP address bindings
+  conflict  DHCP address conflicts
+  database  DHCP database agents
+  import    Show Imported Parameters
+  pool      DHCP pools information
+  relay     Miscellaneous DHCP relay information
+  server    Miscellaneous DHCP server information
+-1#sh ip dhcp binding
+Bindings from all pools not associated with VRF:
+IP address          Client-ID/              Lease expiration        Type
+                    Hardware address/
+                    User name
+.168.101.52      01a8.b1d4.fbc3.9b       Apr 15 2026 05:16 PM    Automatic
+.168.101.53      01a0.cec8.e11f.0f       Apr 15 2026 05:09 PM    Automatic
+-1#
+-1#sh ip dhcp pool voip
+Pool voip :
+ Utilization mark (high/low)    : 100 / 0
+ Subnet size (first/next)       : 0 / 0
+ Total addresses                : 254
+ Leased addresses               : 2
+ Pending event                  : none
+subnet is currently in the pool :
+ Current index        IP address range                    Leased addresses
+.168.101.54       192.168.101.1    - 192.168.101.254   2
+-1#
+</code>
+===== Basic telephony service =====
 <code>
@@ Line 150: / Line 221: @@
 Router(config)#
 </code>
+<code>
+-1(config)#telephony-service
+-1(config-telephony)#ip source-address 192.168.101.102 port 2000
+-1(config-telephony)#ip source-address 192.168.101.11 port 2000
+-1(config-telephony)#
+-1(config-telephony)#crea
+-1(config-telephony)#create cn
+-1(config-telephony)#create cnf-files
+Creating CNF files
+-1(config-telephony)#
+</code>
+Consider this:-
+<code>
+Following voice command is enabled:                    !!
+!!  voice service voip                                   !!
+!!   ip address trusted authenticate                     !!
+!!                                                       !!
+!!The command enables the ip address authentication      !!
+!!on incoming H.323 or SIP trunk calls for toll fraud    !!
+!!prevention supports.                                   !!
+!!                                                       !!
+!!Please use "show ip address trusted list" command      !!
+!!to display a list of valid ip addresses for incoming   !!
+!!H.323 or SIP trunk calls.                              !!
+!!                                                       !!
+!!Additional valid ip addresses can be added via the     !!
+!!following command line:                                !!
+!!  voice service voip                                   !!
+!!   ip address trusted list                             !!
+!!    ipv4 <ipv4-address> [<ipv4 network-mask>]          !!
+</code>
+====== Voice Port ======
 <code>
@@ Line 158: / Line 270: @@
 /2/0           --  fxs-ls      up    dorm on-hook  idle     y
 /2/1           --  fxs-ls      up    dorm on-hook  idle     y
+</code>
+<code>
+ephone-dn  1
+ number 1001
+!
+ephone  1
+ device-security-mode none
+ mac-address A8B1.D4FB.C39B
+ type 7911
+ button  1:1
 </code>
@@ Line 229: / Line 356: @@
 {{:voip:7911-phone.jpg?200|7911 voip phone}}
+==== Factory Reset ====
+  - Start by unplugging the power connector or POE and then plug it back in. The phone will start it's power up cycle.
+  - While the phone is starting up, before the Applications Menu button flashes, press and hold the octothorpe button(#). Continue to hold # until the red LED on the telephone handset flashes.
+  - Release the octothorpe and press all the keypad digits:-  123456789*0#
+  - The phone will reboot and attempt to reconfigure itself.