Differences

This shows you the differences between two versions of the page.

--- networking:atm_glossary [15/01/2025 14:29] – andrew
+++ networking:atm_glossary [24/06/2025 20:24] (current) – andrew
@@ Line 218: / Line 218: @@
 usually be made to filter certain packets (to forward only certain traffic).
-Broadband - a service or system requiring transmission channels capable of supporting rates
+===== Broadband =====
+ - a service or system requiring transmission channels capable of supporting rates
 greater than the Integrated Services Digital Network (ISDN) primary rate.
-Broadband Access - an ISDN access capable of supporting one or more broadband services.
+===== Broadband Access =====
+ - an ISDN access capable of supporting one or more broadband services.
 Brouter (bridging/router) - a device that routes some protocols and bridges others based on
 configuration information.
-Bursty Second - a second during which there were at least the set number of BES threshold
+===== Bursty Second =====
+ - a second during which there were at least the set number of BES threshold
 event errors but fewer than the set number of SES threshold event errors.
-BUS (Broadcast and Unknown Server) - in an emulated LAN, the BUS is responsible for
+===== BUS (Broadcast and Unknown Server) =====
-accepting broadcast, multicast, and unknown unicast packets from the LECs to the broadcast
+ - in an emulated LAN, the BUS is responsible for accepting broadcast, multicast, and unknown unicast packets from the LECs to the broadcast MAC address (FFFFFFFFFFFF) via dedicated point-to-point connections, and forwarding the
-MAC address (FFFFFFFFFFFF) via dedicated point-to-point connections, and forwarding the
 packets to all of the members of the ELAN using a single point-to-multipoint connection.
-CAC (Connection Admission Control) - the procedure used to decide if a request for an
+===== CAC (Connection Admission Control) =====
+ - the procedure used to decide if a request for an
 ATM connection can be accepted based on the attributes of both the requested connection and
 the existing connections.
-Call - an association between two or more users or between a user and a network entity that is
+===== Call =====
+ - an association between two or more users or between a user and a network entity that is
 established by the use of network capabilities. This association may have zero or more connec-
 tions.
-Carrier - a company, such as any of the “baby Bell” companies, that provide network commu-
-nications services, either within a local area or between local areas.
+===== Carrier =====
-CBR (Constant Bit Rate) - a type of traffic that requires a continuous, specific amount of
+ - a company, such as any of the “baby Bell” companies, that provide network communications services, either within a local area or between local areas.
+===== CBR (Constant Bit Rate) =====
+ - a type of traffic that requires a continuous, specific amount of
 bandwidth over the ATM network (e.g., digital information such as video and digitized
 voice).
-CBR port - a port on the CellPath 300 for transmitting and receiving CBR traffic.
+===== CBR port =====
+ - a port on the CellPath 300 for transmitting and receiving CBR traffic.
 cchan - a FORE program used to manage virtual channels on a FORE Systems ATM switch
 running asxd.
-CCITT (Consultative Committee for International Telephone and Telegraph) - an interna-
-tional consultative committee that sets international communications recommendations,
+===== CCITT (Consultative Committee for International Telephone and Telegraph) =====
-which are frequently adopted as standards; develops interface, modem, and data network rec-
+ - an international consultative committee that sets international communications recommendations,
-ommendations. Membership includes PTTs, scientific and trade associations, and private com-
+which are frequently adopted as standards; develops interface, modem, and data network recommendations. Membership includes PTTs, scientific and trade associations, and private companies. CCITT is part of the International Communications Union (a United nations treaty organization in Geneva).
-panies. CCITT is part of the International Communications Union (a United nations treaty
-organization in Geneva).
+===== CDV (Cell Delay Variation) =====
-CDV (Cell Delay Variation) - a quantification of cell clumping for a connection. The cell
+ - a quantification of cell clumping for a connection. The cell
 clumping CDV (yk) is defined as the difference between a cell’s expected reference arrival
 time (ck) and its actual arrival time (ak). The expected reference arrival time (ck) of cell k of a
 specific connection is max . T is the reciprocal of the negotiated peak cell rate.
-CE (Connection Endpoint) - a terminator at one end of a layer connection within a SAP.
-CEI (Connection Endpoint Identifier) - an identifier of a CE that can be used to identify the
+===== CE (Connection Endpoint) =====
+ - a terminator at one end of a layer connection within a SAP.
+===== CEI (Connection Endpoint Identifier) =====
+ - an identifier of a CE that can be used to identify the
 connection at a SAP.
-Cell - an ATM Layer protocol data unit (PDU). The basic unit of information transported in
+===== Cell =====
+ - an ATM Layer protocol data unit (PDU). The basic unit of information transported in
 ATM technology, each 53-byte cell contains a 5-byte header and a 48-byte payload.
-Cell Delineation - the protocol for recognizing the beginning and end of ATM cells within the
+===== Cell Delineation =====
+ - the protocol for recognizing the beginning and end of ATM cells within the
 raw serial bit stream.
-Cell Header - ATM Layer protocol control information.
-c k 1–{ } T a k,+[ ]
+===== Cell Header =====
-Glossary - 6
+ - ATM Layer protocol control information.
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
-Glossary
+===== Cell Port =====
-Cell Port - a port on the CellPath 300 that transmits and receives traffic in cell format.
+ - a port on the CellPath 300 that transmits and receives traffic in cell format.
-Cell Rate Adaptation - a function performed by a protocol module in which empty cells
+===== Cell Rate Adaptation =====
+ - a function performed by a protocol module in which empty cells
 (known as unassigned cells) are added to the output stream. This is because there always must
 be a fixed number of cells in the output direction; when there are not enough cells to transmit,
 unassigned cells are added to the output data stream.
-Cell Transfer Delay - the transit delay of an ATM cell successfully passed between two desig-
+===== Cell Transfer Delay =====
+ - the transit delay of an ATM cell successfully passed between two desig-
 nated boundaries.
-CES (Circuit emulation Services) - The CellPath 90 supports Circuit Emulation Services
+===== CES (Circuit emulation Services) =====
+ - The CellPath 90 supports Circuit Emulation Services
 (CES) for applications requiring a fixed delay, lossless end-to-end connection through the net-
 work. In essence, CES provides a virtual private line service to the connecting application.
 Channelization - capability of transmitting independent signals together over a cable while
 still maintaining their separate identity for later separation.
-CLP (Cell Loss Priority) - the last bit of byte four in an ATM cell header; indicates the eligibil-
+===== CLP (Cell Loss Priority) =====
+ - the last bit of byte four in an ATM cell header; indicates the eligibil-
 ity of the cell for discard by the network under congested conditions. If the bit is set to 1, the
 cell may be discarded by the network depending on traffic conditions.
-Cold Start Trap - a CellPath 300 SNMP trap which is sent when the unit has been power-
+===== Cold Start Trap =====
+ - a CellPath 300 SNMP trap which is sent when the unit has been power-
 cycled (see trap).
-Comm Port - the front panel DCE port that allows access to the CellPath 300 user interface via
+===== Comm Port =====
+ - the front panel DCE port that allows access to the CellPath 300 user interface via
 a connected terminal.
-Concentrator - a communications device that offers the ability to concentrate many lower-
+===== Concentrator =====
+ - a communications device that offers the ability to concentrate many lower-
 speed channels into and out of one or more high-speed channels.
-Congestion Management - a CellPath 300 feature that helps ensure reasonable service for
+===== Congestion Management =====
+ - a CellPath 300 feature that helps ensure reasonable service for
 VBR connections in an ATM network. For each connection, the CellPath 300 maintains a prior-
 ity, sustained cell rate (SCR), and peak cell rate (PCR). During times of congestion, the CellPath
 reduces the bandwidth to the SCR, based on the priority of the connection.
-Connection - the concatenation of ATM Layer links in order to provide an end-to-end infor-
+===== Connection =====
+ - the concatenation of ATM Layer links in order to provide an end-to-end infor-
 mation transfer capability to access points.
-Connectionless Service - a type of service in which no pre-determined path or link has been
+===== Connectionless Service =====
+ - a type of service in which no pre-determined path or link has been
 established for transfer of information, supported by AAL 4.
-Connection-Oriented Service - a type of service in which information always traverses the
+===== Connection-Oriented Service =====
+ - a type of service in which information always traverses the
 same pre-established path or link between two points, supported by AAL 3.
-Controlled Slip - a situation in which one frame’s worth of data is either lost or replicated. A
+===== Controlled Slip =====
+ - a situation in which one frame’s worth of data is either lost or replicated. A
 controlled slip typically occurs when the sending device and receiving device are not using
 the same clock.
-Corresponding Entities - peer entities with a lower layer connection among them
+===== Corresponding Entities =====
+ - peer entities with a lower layer connection among them
-cpath - a FORE program used to manage virtual paths on a FORE Systems ATM switch run-
-ning asxd.
+===== cpath =====
-CPE (Customer Premise Equipment) - equipment that is on the customer side of the point of
+ - a FORE program used to manage virtual paths on a FORE Systems ATM switch running asxd.
+===== CPE (Customer Premise Equipment) =====
+ - equipment that is on the customer side of the point of
 demarcation, as opposed to equipment that is on a carrier side. See also point of demarcation.
 cport - a FORE program used to monitor and change the state of ports on a FORE Systems
 ATM switch running asxd.
-CRC (Cyclic Redundancy Check) - an error detection scheme in which a number is derived
+===== CRC (Cyclic Redundancy Check) =====
+ - an error detection scheme in which a number is derived
 from the data that will be transmitted. By recalculating the CRC at the remote end and com-
 paring it to the value originally transmitted, the receiving node can detect errors.
 Cross Connection - a mapping between two channels or paths at a network device such as
 the CellPath 300.
-CD (Controlled Slip) - a situation in which one frame’s worth of data is either lost or repli-
+===== CD (Controlled Slip) =====
+ - a situation in which one frame’s worth of data is either lost or repli-
 cated. A controlled slip typically occurs when the sending device and receiving device are not
 using the same clock.
-CS (Convergence Sublayer) - a portion of the AAL. Data is passed first to the CS where it is
+===== CS (Convergence Sublayer) =====
+ - a portion of the AAL. Data is passed first to the CS where it is
 divided into rational, fixed-length packets or PDUs (Protocol Data Units). For example, AAL 4
 processes user data into blocks that are a maximum of 64 kbytes long.
@@ Line 326: / Line 379: @@
 the DTE on pin 5) which indicates that the attached DTE may begin transmitting; issuance in
 response to the DTE’s RTS.
-D4 framing - See SF)
-DARPA (Defense Advanced Research Projects Agency) - the US government agency that
+===== D4 framing =====
-funded the ARPANET.
+ - See SF)
-Datagram - a packet of information used in a connectionless network service that is routed to
+===== DARPA (Defense Advanced Research Projects Agency) =====
+ - the US government agency that funded the ARPANET.
+===== Datagram =====
+ - a packet of information used in a connectionless network service that is routed to
 its destination using an address included in the datagram’s header.
 DCE (Data Communications Equipment) - a definition in the RS232C standard that
 describes the functions of the signals and the physical characteristics of an interface for a com-
 munication device such as a modem.
-DCS (Digital Cross-connect System) - an electronic patch panel used to route digital signals
-in a central office.
+===== DCS (Digital Cross-connect System) =====
-Demultiplexing - a function performed by a layer entity that identifies and separates SDUs
+ - an electronic patch panel used to route digital signals in a central office.
+===== Demultiplexing =====
+ - a function performed by a layer entity that identifies and separates SDUs
 from a single connection to more than one connection (see multiplexing).
 DFA (DXI Frame Address) - a connection identifier associated with ATM DXI packets that
 serves the same functions as, and translates directly to, the VPI/VCI on an ATM cell.
-Glossary - 8
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
-Glossary
+===== DIP Switch (Dual In-line Package) =====
-DIP Switch (Dual In-line Package) - a device that has two parallel rows of contacts that let
+ - a device that has two parallel rows of contacts that let
 the user switch electrical current through a pair of those contacts to on or off. They are used to
 reconfigure components and peripherals.
 DLCI (Data Link Connection Identifier) - a connection identifier associated with frame relay
-packets that serves the same functions as, and translates directly to, the VPI/VCI on an ATM
+packets that serves the same functions as, and translates directly to, the VPI/VCI on an ATM cell.
-cell.
-Domain Name Server - a computer that converts names to their corresponding Internet num-
+===== Domain Name Server =====
+ - a computer that converts names to their corresponding Internet num-
 bers. It allows users to telnet or FTP to the name instead of the number.
-DNS (Domain Name System) - the distributed name and address mechanism used in the
-Internet.
+===== DNS (Domain Name System) =====
-DSn (Digital Standard n (0, 1, 1C, 2, and 3)) - a method defining the rate and format of digi-
+ - the distributed name and address mechanism used in the Internet.
-tal hierarchy, with asynchronous data rates defined as follows:
-DS0 64kbps 1 voice channel
+===== DSn (Digital Standard n (0, 1, 1C, 2, and 3)) =====
-DS1 1.544Mbps 24 DS0s
+ - a method defining the rate and format of digital hierarchy, with asynchronous data rates defined as follows:
-DS1C 3.152 Mbps 2 DS1s
+  - DS0 64kbps 1 voice channel
-DS2 6.312 Mbps 4 DS1s
+  - DS1 1.544Mbps 24 DS0s
-DS3 44.736 Mbps 28 DS1s
+  - DS1C 3.152 Mbps 2 DS1s
-Synchronous data rates (SONET) are defined as:
+  - DS2 6.312 Mbps 4 DS1s
-STS-1/OC-1 51.84 Mbps 28 DS1s or 1 DS3
+  - DS3 44.736 Mbps 28 DS1s
-STS-3/OC-3 155.52 Mbps 3 STS-1s byte interleaved
-STS-3c/OC-3c 155.52 Mbps Concatenated, indivisible payload
+    Synchronous data rates (SONET) are defined as:
-STS-12/OC-12 622.08 Mbps 12 STS-1s, 4 STS-3cs, or any mixture
+  - STS-1/OC-1 51.84 Mbps 28 DS1s or 1 DS3
-STS-12c/OC-12c 622.08 Mbps Concatenated, indivisible payload
+  - STS-3/OC-3 155.52 Mbps 3 STS-1s byte interleaved
-STS-48/OC-48 2488.32 Mbps 48 STS-1s, 16 STS-3cs, or any mixture
+  - STS-3c/OC-3c 155.52 Mbps Concatenated, indivisible payload
-DSR (Data Set Ready) - an RS-232 modem interface control signal (sent from the modem to
+  - STS-12/OC-12 622.08 Mbps 12 STS-1s, 4 STS-3cs, or any mixture
-the DTE on pin 6) which indicates that the modem is connected to the telephone circuit. Usu-
+  - STS-12c/OC-12c 622.08 Mbps Concatenated, indivisible payload
-ally a prerequisite to the DTE issuing RTS.
+  - STS-48/OC-48 2488.32 Mbps 48 STS-1s, 16 STS-3cs, or any mixture
-DTE (Data Terminal Equipment) - generally user devices, such as terminals and computers,
+===== DSR (Data Set Ready) =====
+ - an RS-232 modem interface control signal (sent from the modem to
+the DTE on pin 6) which indicates that the modem is connected to the telephone circuit. Usually a prerequisite to the DTE issuing RTS.
+===== DTE (Data Terminal Equipment) =====
+ - generally user devices, such as terminals and computers,
 that connect to data circuit-terminating equipment. They either generate or receive the data
 carried by the network.
-DTR (Data Terminal Ready) - an RS232 modem interface control signal (sent from the DTE to
+===== DTR (Data Terminal Ready) =====
+ - an RS232 modem interface control signal (sent from the DTE to
 the modem on pin 20) which indicates that the DTE is ready for data transmission and which
 requests that the modem be connected to the telephone circuit.
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual Glossary - 9
-Glossary
+===== DXI =====
-Glossary
+ - a generic phrase used in the full names of several protocols, all commonly used to allow
-DXI - a generic phrase used in the full names of several protocols, all commonly used to allow
 a pair of DCE and DTE devices to share the implementation of a particular WAN protocol. The
 protocols all define the packet formats used to transport data packets between DCE and DTE
 devices.
-E1 - Wide-area digital transmission scheme used predominantly in Europe that carries data at
+===== E1 =====
+ - Wide-area digital transmission scheme used predominantly in Europe that carries data at
 a rate of 2.048 Mbps. E1 lines can be leased for private use from common carriers.
-E3 - Wide-area digital transmission scheme used predominantly in Europe that carries data at
+===== E3 =====
+ - Wide-area digital transmission scheme used predominantly in Europe that carries data at
 a rate of 34.368 Mbps. E3 lines can be leased for private use from common carriers.
-EEPROM (Electrically Erasable Programmable Read Only Memory) - an EPROM that can
-be cleared with electrical signals rather than the traditional ultraviolet light.
+===== EEPROM (Electrically Erasable Programmable Read Only Memory) =====
-EFCI (Explicit Forward Congestion Indication) - the second bit of the payload type field in
+ - an EPROM that can be cleared with electrical signals rather than the traditional ultraviolet light.
-the header of an ATM cell, the EFCI bit indicates network congestion to receiving hosts. On a
-congested switch, the EFCI bit is set to “1” by the transmitting network module when a certain
+===== EFCI (Explicit Forward Congestion Indication) =====
-number of cells have accumulated in the network module’s shared memory buffer. When a
+ - the second bit of the payload type field in the header of an ATM cell, the EFCI bit indicates network congestion to receiving hosts. On a congested switch, the EFCI bit is set to “1” by the transmitting network module when a certain number of cells have accumulated in the network module’s shared memory buffer. When a cell is received that has its EFCI bit set to “1,” the receiving host notifies the sending host, which should then reduce its transmission rate.
-cell is received that has its EFCI bit set to “1,” the receiving host notifies the sending host,
-which should then reduce its transmission rate.
+===== EGP (Exterior Gateway) Protocol =====
-EGP (Exterior Gateway) Protocol - used by gateways in an internet, connecting autonomous
+ - used by gateways in an internet, connecting autonomous networks.
-networks.
-EIA (Electronics Industries Association) - a USA trade organization that issues its own
+===== EIA (Electronics Industries Association) =====
+ - a USA trade organization that issues its own
 standards and contributes to ANSI; developed RS-232. Membership includes USA manufac-
 turers.
-EISA (Extended Industry Standard Architecture) - a bus architecture for desktop computers
+===== EISA (Extended Industry Standard Architecture) =====
+ - a bus architecture for desktop computers
 that provides a 32-bit data passage while maintaining compatibility with the ISA or AT archi-
 tecture.
-elarp - a FORE program that shows and manipulates MAC and ATM address mappings for
-LAN Emulation Clients (LECs).
+===== elarp =====
-elconfig - a FORE program that shows and modifies LEC configuration. Allows the user to set
+ - a FORE program that shows and manipulates MAC and ATM address mappings for LAN Emulation Clients (LECs).
+===== elconfig =====
+ - a FORE program that shows and modifies LEC configuration. Allows the user to set
 the NSAP address of the LAN Emulation Configuration Server (LECS), display the list of
 Emulated LANs (ELANs) configured in the LECS for this host, display the list of ELANs
 locally configured along with the membership state of each, and locally administer ELAN
 membership.
-EM - the CellPath 300 extension module; paired with the system controller and supporting an
+===== EM =====
+ - the CellPath 300 extension module; paired with the system controller and supporting an
 optional PCMCIA card.
-Embedded SNMP Agent - an SNMP agent can come in two forms: embedded or proxy. An
+===== Embedded SNMP Agent =====
+ - an SNMP agent can come in two forms: embedded or proxy. An
 embedded SNMP agent is integrated into the physical hardware and software of the unit. The
 CellPath 300 has an internal, integrated SNMP agent.
-Glossary - 10
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
+===== EMI (Electromagnetic Interference) =====
-Glossary
+ - signals generated and radiated by an electronic device
-EMI (Electromagnetic Interference) - signals generated and radiated by an electronic device
 that cause interference with radio communications, among other effects.
 End-to-End Connection - when used in reference to an ATM network, a connection that trav-
 els through an ATM network, passing through various ATM devices and with endpoints at the
 termination of the ATM network.
-EPROM - Erasable Programmable Read Only Memory (see PROM).
-EQL (Equalization) - the process of compensating for line distortions.
+===== EPROM =====
-ES (End System) - a system in which an ATM connection is terminated or initiated. An origi-
+ - Erasable Programmable Read Only Memory (see PROM).
+===== EQL (Equalization) =====
+ - the process of compensating for line distortions.
+===== ES (End System) =====
+ - a system in which an ATM connection is terminated or initiated. An origi-
 nating end system initiates the ATM connection, and a terminating end system terminates the
 ATM connection. OAM cells may be generated and received.
-ES (Errored Seconds) - a second during which at least one code violation occurred.
-ESF (Extended Superframe) - T1 framing standard that provides frame synchronization,
+===== ES (Errored Seconds) =====
-cyclic redundancy, and data link bits.
+ - a second during which at least one code violation occurred.
-Ethernet - a 10-Mbps, coaxial standard for LANs in which all nodes connect to the cable
+===== ESF (Extended Superframe) =====
+ - T1 framing standard that provides frame synchronization, cyclic redundancy, and data link bits.
+===== Ethernet =====
+ - a 10-Mbps, coaxial standard for LANs in which all nodes connect to the cable
 where they contend for access.
-Fairness - as related to Generic Flow Control (GFC), fairness is defined as meeting all of the
+===== Fairness =====
+ - as related to Generic Flow Control (GFC), fairness is defined as meeting all of the
 agreed quality of service (QoS) requirements by controlling the order of service for all active
 connections.
-Far-End - in a relationship between two devices in a circuit, the far-end device is the one that
+===== Far-End =====
+ - in a relationship between two devices in a circuit, the far-end device is the one that
 is remote.
-FCC - a board of commissioners appointed by the President under the Communications Act of
+===== FCC =====
+ - a board of commissioners appointed by the President under the Communications Act of
 , with the authority to regulate all interstate telecommunications originating in the United
 States, including transmission over phone lines.
-FDDI (Fiber Distributed Data Interface) - high-speed data network that uses fiber-optic as
+===== FDDI (Fiber Distributed Data Interface) =====
+ - high-speed data network that uses fiber-optic as
 the physical medium. Operates in similar manner to Ethernet or Token Ring, only faster.
-FDM (Frequency Division Multiplexing) - a method of dividing an available frequency range
+===== FDM (Frequency Division Multiplexing) =====
+ - a method of dividing an available frequency range
 into parts with each having enough bandwidth to carry one channel.
-FEBE (Far End Block Error) - an error detected by extracting the 4-bit FEBE field from the
+===== FEBE (Far End Block Error) =====
+ - an error detected by extracting the 4-bit FEBE field from the
 path status byte (G1). The legal range for the 4-bit field is between 0000 and 1000, representing
 zero to eight errors. Any other value is interpreted as zero errors.
-FECN (Forward Explicit Congestion Notification) - bit set by a Frame Relay network to
+===== FECN (Forward Explicit Congestion Notification) =====
+ - bit set by a Frame Relay network to
 inform data terminal equipment (DTE) receiving the frame that congestion was experienced in
 the path from source to destination. DTE receiving frames with the FECN bit set can request
 that higher-level protocols take flow control action as appropriate. Compare with BECN.
+===== FERF (Far End Receive Failure) =====
+ - a line error asserted when a 110 binary pattern is detected
+in bits 6, 7, 8 of the K2 byte for five consecutive frames. A line FERF is removed when any pattern other than 110 is detected in these bits for five consecutive frames.
+===== FIFO (First-In, First-Out) =====
+ - a method of coordinating the sequential flow of data through a buffer.
+===== Flag =====
+ - a specific bit pattern used to identify the beginning or end of a frame.
-FERF (Far End Receive Failure) - a line error asserted when a 110 binary pattern is detected
-in bits 6, 7, 8 of the K2 byte for five consecutive frames. A line FERF is removed when any pat-
-tern other than 110 is detected in these bits for five consecutive frames.
-FIFO (First-In, First-Out) - a method of coordinating the sequential flow of data through a
-buffer.
-Flag - a specific bit pattern used to identify the beginning or end of a frame.
 Frame - a variable length group of data bits with a specific format containing flags at the
 beginning and end to provide demarcation.
-Frame Relay - a fast packet switching protocol based on the LAPD protocol of ISDN that per-
+===== Frame Relay =====
+ - a fast packet switching protocol based on the LAPD protocol of ISDN that per-
 forms routing and transfer with less overhead processing than X.25.
-Frame Synchronization Error - an error in which one or more time slot framing bits are in
+===== Frame Synchronization Error =====
+ - an error in which one or more time slot framing bits are in
 error.
-Framing - a protocol that separates incoming bits into identifiable groups so that the receiving
+===== Framing =====
+ - a protocol that separates incoming bits into identifiable groups so that the receiving
 multiplexer recognizes the grouping.
-FT-PNNI (ForeThought PNNI) - a FORE Systems routing and signalling protocol that uses pri-
-vate ATM (NSAP) addresses; a precursor to ATM Forum PNNI (see PNNI).
+===== FT-PNNI (ForeThought PNNI) =====
-FTP (File Transfer Protocol) - a TCP/IP protocol that lets a user on one computer access, and
+ - a FORE Systems routing and signalling protocol that uses private ATM (NSAP) addresses; a precursor to ATM Forum PNNI (see PNNI).
+===== FTP (File Transfer Protocol) =====
+ - a TCP/IP protocol that lets a user on one computer access, and
 transfer data to and from, another computer over a network. ftp is usually the name of the
 program the user invokes to accomplish this task.
-GCRA (Generic Cell Rate Algorithm) - an algorithm which is employed in traffic policing
+===== GCRA (Generic Cell Rate Algorithm) =====
+ - an algorithm which is employed in traffic policing
 and is part of the user/network service contract. The GCRA is a scheduling algorithm which
 ensures that cells are marked as conforming when they arrive when expected or later than
 expected and non-conforming when they arrive sooner than expected.
-GFC (Generic Flow Control) - the first four bits of the first byte in an ATM cell header. Used
+===== GFC (Generic Flow Control) =====
+ - the first four bits of the first byte in an ATM cell header. Used
 to control the flow of traffic across the User-to-Network Interface (UNI), and thus into the net-
 work. Exact mechanisms for flow control are still under investigation and no explicit defini-
@@ Line 487: / Line 605: @@
 (between network nodes), these four bits provide additional network address capacity, and
 are appended to the VPI field.)
-GIO - a proprietary bus architecture used in certain Silicon Graphics, Inc. workstations.
-Header - protocol control information located at the beginning of a protocol data unit.
+===== GIO =====
-HDB3 (High Density Bipolar) - line-code type standard for T1 where each block of three zeros
+ - a proprietary bus architecture used in certain Silicon Graphics, Inc. workstations.
+===== Header =====
+ - protocol control information located at the beginning of a protocol data unit.
+===== HDB3 (High Density Bipolar) =====
+ - line-code type standard for T1 where each block of three zeros
 is replaced by 00V or B0V, where B represents an inserted pulse conforming to the AMI rule
 (ITU-T G.701, item 9004) and V represents an AMI violation (ITU-T G.701, item 9007). The
@@ Line 495: / Line 619: @@
 odd (successive V pulses are of alternate polarity so that no d.c. component is introduced).
 Compare with AMI.
-Glossary - 12
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
-Glossary
+===== HDLC (High-Level Data Link Control) =====
-HDLC (High-Level Data Link Control) - Bit-oriented synchronous data link layer protocol
+ - Bit-oriented synchronous data link layer protocol
 developed by the ISO. Derived from SDLC, HDLC specifies a data encapsulation method on
 synchronous serial links using frame characters and checksums. See also SDLC.
-HEC (Header Error Control) - a CRC code located in the last byte of an ATM cell header that
+===== HEC (Header Error Control) =====
+ - a CRC code located in the last byte of an ATM cell header that
 is used for checking cell integrity only.
-HIPPI (High Performance Parallel Interface) - ANSI standard that extends the computer bus
+===== HIPPI (High Performance Parallel Interface) =====
+ - ANSI standard that extends the computer bus
 over fairly short distances at speeds of 800 and 1600 Mbps.
-HPUX - the Hewlett-Packard version of UNIX.
-HSSI (High-Speed Serial Interface) - a serial communications connection that operates at
+===== HPUX =====
+ - the Hewlett-Packard version of UNIX.
+===== HSSI (High-Speed Serial Interface) =====
+ - a serial communications connection that operates at
 speeds of up to 1.544 Mbps.
-Hub - a device that connects several other devices, usually in a star topology.
-I/O Module - FORE’s interface cards for the LAX-20 LAN Access Switch, designed to connect
+===== Hub =====
+ - a device that connects several other devices, usually in a star topology.
+===== I/O Module =====
+ - FORE’s interface cards for the LAX-20 LAN Access Switch, designed to connect
 Ethernet, Token Ring, and FDDI LANs to ForeRunner ATM networks.
-ICMP (Internet Control Message Protocol) - the protocol that handles errors and control
+===== ICMP (Internet Control Message Protocol) =====
+ - the protocol that handles errors and control
 messages at the IP layer. ICMP is actually a part of the IP protocol layer. It can generate error
 messages, test packets, and informational messages related to IP.
-IEEE (Institute of Electrical and Electronics Engineers) - the world’s largest technical pro-
+===== IEEE (Institute of Electrical and Electronics Engineers) =====
+ - the world’s largest technical pro-
 fessional society. Based in the U.S., the IEEE sponsors technical conferences, symposia & local
 meetings worldwide, publishes nearly 25% of the world’s technical papers in electrical, elec-
 tronics & computer engineering, provides educational programs for members, and promotes
 standardization.
 IETF (Internet Engineering Task Force) - a large, open, international community of network
 designers, operators, vendors and researchers whose purpose is to coordinate the operation,
-management and evolution of the Internet to resolve short- and mid-range protocol and archi-
+management and evolution of the Internet to resolve short- and mid-range protocol and architectural issues.
-tectural issues.
-ILMI (Interim Local Management Interface) - the standard that specifies the use of the Sim-
+===== ILMI (Interim Local Management Interface) =====
-ple Network Management Protocol (SNMP) and an ATM management information base
+ - the standard that specifies the use of the Simple Network Management Protocol (SNMP) and an ATM management information base (MIB) to provide network status and configuration information.
-(MIB) to provide network status and configuration information.
-Interface Data - the unit of information transferred to/from the upper layer in a single inter-
+===== Interface Data =====
+ - the unit of information transferred to/from the upper layer in a single inter-
 action across a SAP. Each Interface Data Unit (IDU) controls interface information and may
 also contain the whole or part of the SDU.
-internet - while an internet is a network, the term “internet” is usually used to refer to a collec-
+===== internet =====
+ - while an internet is a network, the term “internet” is usually used to refer to a collec-
 tion of networks interconnected with routers.
-Internet - (note the capital “I”) the largest internet in the world including large national back-
+===== Internet =====
+ - (note the capital “**I**”) the largest internet in the world including large national back-
 bone nets and many regional and local networks worldwide. The Internet uses the TCP/IP
 suite. Networks with only e-mail connectivity are not considered on the Internet.
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual Glossary - 13
-Glossary
+===== Internet Addresses =====
-Glossary
+ - the numbers used to identify hosts on an internet network.
-Internet Addresses - the numbers used to identify hosts on an internet network. Internet host
-numbers are divided into two parts; the first is the network number and the second, or local,
+Internet host numbers are divided into two parts; the first is the network number and the second, or local,
 part is a host number on that particular network. There are also three classes of networks in
 the Internet, based on the number of hosts on a given network. Large networks are classified
@@ Line 546: / Line 692: @@
 range 192-254 with a maximum of 254 hosts. Addresses are given as dotted decimal numbers
 in the following format:
 nnn.nnn.nnn.nnn
 In a Class A network, the first of the numbers is the network number, the last three numbers
 are the local host address.
 In a Class B network, the first two numbers are the network, the last two are the local host
 address.
 In a Class C network, the first three numbers are the network address, the last number is the
 local host address.
 The following table summarizes the classes and sizes:
-Class First # Max# Hosts
+^ Class ^ First ^ # Max# Hosts^
-A 1-126 16,387,064
+| A | 1-126 16,387,064|
-B 129-191 64,516
+| B | 129-191 64,516|
-C 192-223 254
+| C | 192-223 254|
 Network mask values are used to identify the network portion and the host portion of the
 address. For:
-Class A - the default mask is 255.0.0.0
+  - Class A - the default mask is 255.0.0.0
-Class B - the default mask is 255.255.0.0
+  - Class B - the default mask is 255.255.0.0
-Class C - the default mask is 255.255.255.0
+  - Class C - the default mask is 255.255.255.0
 Subnet masking is used when a portion of the host ID is used to identify a subnetwork. For
 example, if a portion of a Class B network address is used for a subnetwork, the mask could be
@@ Line 572: / Line 723: @@
 commonly see IP addresses written in “dot” notation; for instance, 192.228.32.14 (see IP net-
 mask).
-Glossary - 14
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
+===== IP Netmask =====
-Glossary
+ - a pattern of 32 bits that is combined with an IP address to determine which bits
-IP Netmask - a pattern of 32 bits that is combined with an IP address to determine which bits
 of an IP address denote the network number and which denote the host number. Netmasks
 are useful for sub-dividing IP networks. IP netmasks are written in “dot” notation; for
 instance, 255.255.255.0 (see IP address).
-IPX Protocol (Internetwork Packet Exchange) - a NetWare protocol similar to the Xerox
+===== IPX Protocol =====
+ (Internetwork Packet Exchange) - a NetWare protocol similar to the Xerox
 Network Systems (XNS) protocol that provides datagram delivery of messages.
-IS (Intermediate system) - a system that provides forwarding functions or relaying functions
+===== IS (Intermediate system) =====
+ - a system that provides forwarding functions or relaying functions
 or both for a specific ATM connection. OAM cells may be generated and received.
-ISA Bus - a bus standard developed by IBM for expansion cards in the first IBM PC. The orig-
+===== ISA Bus =====
+ - a bus standard developed by IBM for expansion cards in the first IBM PC. The orig-
 inal bus supported a data path only 8 bits wide. IBM subsequently developed a 16-bit version
 for its AT class computers. The 16-bit AT ISA bus supports both 8- and 16-bit cards. The 8-bit
 bus is commonly called the PC/XT bus, and the 16-bit bus is called the AT bus.
-ISDN (Integrated Services Digital Network) - an emerging technology that is beginning to be
+===== ISDN (Integrated Services Digital Network) =====
+ - an emerging technology that is beginning to be
 offered by the telephone carriers of the world. ISDN combines voice and digital network ser-
 vices into a single medium or wire.
-ISO (International Standards Organization) - a voluntary, non treaty organization founded
+===== ISO (International Standards Organization) =====
+ - a voluntary, non treaty organization founded
 in 1946 that is responsible for creating international standards in many areas, including com-
 puters and communications.
-Isochronous - signals carrying embedded timing information or signals that are dependent
+===== Isochronous =====
+ - signals carrying embedded timing information or signals that are dependent
 on uniform timing; usually associated with voice and/or video transmission.
-ITU (International Telecommunications Union) - the telecommunications agency of the
-United Nations, established to provide standardized communications procedures and prac-
+===== ITU (International Telecommunications Union) =====
-tices, including frequency allocation and radio regulations, on a worldwide basis.
+ - the telecommunications agency of the
-J2 - Wide-area digital transmission scheme used predominantly in Japan that carries data at a
+United Nations, established to provide standardized communications procedures and practices, including frequency allocation and radio regulations, on a worldwide basis.
+===== J2 =====
+ - Wide-area digital transmission scheme used predominantly in Japan that carries data at a
 rate of 6.312 Mbps.
-Jitter - analog communication line distortion caused by variations of a signal from its refer-
+===== Jitter =====
+ - analog communication line distortion caused by variations of a signal from its refer-
 ence timing position.
-Jumper - a patch cable or wire used to establish a circuit, often temporarily, for testing or diag-
+===== Jumper =====
+ - a patch cable or wire used to establish a circuit, often temporarily, for testing or diag-
 nostics; also, the devices, shorting blocks, used to connect adjacent exposed pins on a printed
 circuit board that control the functionality of the card.
-LAN (Local Area Network) - a data network intended to serve an area of only a few square
+===== LAN (Local Area Network) =====
+ - a data network intended to serve an area of only a few square
 kilometers or less. Because the network is known to cover only a small area, optimizations can
 be made in the network signal protocols that permit higher data rates.
-lane - a program that provides control over the execution of the LAN Emulation Server (LES),
+===== lane =====
+ - a program that provides control over the execution of the LAN Emulation Server (LES),
 Broadcast/Unknown Server (BUS), and LAN Emulation Configuration Server (LECS) on the
 local host.
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual Glossary - 15
-Glossary
+===== LAN Access Concentrator =====
-Glossary
+ - a LAN access device that allows a shared transmission medium
-LAN Access Concentrator - a LAN access device that allows a shared transmission medium
 to accommodate more data sources than there are channels currently available within the
 transmission medium.
-LAPB (Link Access Procedure, Balanced) - Data link protocol in the X.25 protocol stack.
+===== LAPB =====
+ (Link Access Procedure, Balanced) - Data link protocol in the X.25 protocol stack.
 LAPB is a bit-oriented protocol derived from HDLC. See also HDLC and X.25.
-LAX-20 - a FORE Systems LAN Access Switch, designed to connect Ethernet, Token Ring, and
+===== LAX-20 =====
+ - a FORE Systems LAN Access Switch, designed to connect Ethernet, Token Ring, and
 FDDI LANs to ForeRunner ATM networks. The LAX-20 is a multiport, multiprotocol internet-
 working switch that combines the advantages of a high-performance LAN switch and a full-
 featured ATM interface capable of carrying LAN traffic.
-Layer Entity - an active layer within an element.
-Layer Function - a part of the activity of the layer entities.
+===== Layer Entity =====
-Layer Service - a capability of a layer and the layers beneath it that is provided to the upper
+ - an active layer within an element.
+===== Layer Function =====
+ - a part of the activity of the layer entities.
+===== Layer Service =====
+ - a capability of a layer and the layers beneath it that is provided to the upper
 layer entities at the boundary between that layer and the next higher layer.
-Layer User Data - the information transferred between corresponding entities on behalf of the
+===== Layer User Data =====
+ - the information transferred between corresponding entities on behalf of the
 upper layer or layer management entities for which they are providing services.
-le - a FORE program that implements both the LAN Emulation Server (LES) and the Broad-
+===== le =====
+ - a FORE program that implements both the LAN Emulation Server (LES) and the Broad-
 cast/Unknown Server (BUS).
-LEC (LAN Emulation Client) - the component in an end system that performs data forward-
-ing, address resolution, and other control functions when communicating with other compo-
+===== LEC (LAN Emulation Client) =====
-nents within an ELAN.
+ - the component in an end system that performs data forwarding, address resolution, and other control functions when communicating with other components within an ELAN.
-lecs - a FORE program that implements the assignment of individual LECs to different emu-
-lated LANs.
+===== lecs =====
-LECS (LAN Emulation Configuration Server) - the LECS is responsible for the initial config-
+ - a FORE program that implements the assignment of individual LECs to different emulated LANs.
-uration of LECs. It provides information about available ELANs that a LEC may join, together
-with the addresses of the LES and BUS associated with each ELAN.
+===== LECS (LAN Emulation Configuration Server) =====
-leq - a FORE program that provides information about an ELAN. This information is obtained
+ - the LECS is responsible for the initial configuration of LECs. It provides information about available ELANs that a LEC may join, together with the addresses of the LES and BUS associated with each ELAN.
+===== leq =====
+ - a FORE program that provides information about an ELAN. This information is obtained
 from the LES, and includes MAC addresses registered on the ELAN together with their corre-
 sponding ATM addresses.
-LES (LAN Emulation Server) - the LES implements the control coordination function for an
+===== LES (LAN Emulation Server) =====
+ - the LES implements the control coordination function for an
 ELAN. The LES provides the service of registering and resolving MAC addresses to ATM
 addresses.
-Link Down Trap - a CellPath 300 SNMP trap that signifies that the Ethernet interface has tran-
-sitioned from a normal state to an error state, or has been disconnected.
+===== Link Down Trap =====
-Link Up Trap - a CellPath 300 SNMP trap that signifies that the Ethernet interface has transi-
+ - a CellPath 300 SNMP trap that signifies that the Ethernet interface has transitioned from a normal state to an error state, or has been disconnected.
-tioned from an error condition to a normal state.
-Glossary - 16
+===== Link Up Trap =====
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
+ - a CellPath 300 SNMP trap that signifies that the Ethernet interface has transitioned from an error condition to a normal state.
-Glossary
-LLC (Logical Link Control) - a protocol developed by the IEEE 802 committee for data-link-
-layer transmission control; the upper sublayer of the IEEE Layer 2 (OSI) protocol that comple-
+===== LLC (Logical Link Control) =====
-ments the MAC protocol; IEEE standard 802.2; includes end-system addressing and error
+ - a protocol developed by the IEEE 802 committee for data-link-
+layer transmission control; the upper sublayer of the IEEE Layer 2 (OSI) protocol that complements the MAC protocol; IEEE standard 802.2; includes end-system addressing and error
 checking.
-LOF (Loss Of Frame) - a type of transmission error that may occur in wide-area carrier lines.
-Loopback - a troubleshooting technique that returns a transmitted signal to its source so that
+===== LOF (Loss Of Frame) =====
+ - a type of transmission error that may occur in wide-area carrier lines.
+===== Loopback =====
+ - a troubleshooting technique that returns a transmitted signal to its source so that
 the signal can be analyzed for errors. Typically, a loopback is set at various points in a line
 until the section of the line that is causing the problem is discovered.
-looptest - a program that tests the interface for basic cell reception and transmission function-
-ality. It is usually used for diagnostic purposes to determine if an interface is functioning prop-
+===== looptest =====
-erly.
+ - a program that tests the interface for basic cell reception and transmission functionality. It is usually used for diagnostic purposes to determine if an interface is functioning properly.
-LOP (Loss Of Pointer) - a type of transmission error that may occur in wide-area carrier lines.
-LOS (Loss Of Signal) - a type of transmission error that may occur in wide-area carrier lines.
+===== LOP (Loss Of Pointer) =====
-MAC (Media Access Control) - a media-specific access control protocol within IEEE 802 spec-
+ - a type of transmission error that may occur in wide-area carrier lines.
-ifications; currently includes variations for Token Ring, token bus, and CSMA/CD; the lower
+===== LOS (Loss Of Signal) =====
+ - a type of transmission error that may occur in wide-area carrier lines.
+===== MAC (Media Access Control) =====
+ - a media-specific access control protocol within IEEE 802 specifications; currently includes variations for Token Ring, token bus, and CSMA/CD; the lower
 sublayer of the IEEE's link layer (OSI), which complements the Logical Link Control (LLC).
-MAU (Media Attachment Unit) - device used in Ethernet and IEEE 802.3 networks that pro-
-vides the interface between the AUI port of a station and the common medium of the Ether-
+===== MAU (Media Attachment Unit) =====
-net. The MAU, which can be built into a station or can be a separate device, performs physical
+ - device used in Ethernet and IEEE 802.3 networks that provides the interface between the AUI port of a station and the common medium of the Ethernet. The MAU, which can be built into a station or can be a separate device, performs physical layer functions including conversion of the digital data from the Ethernet interface, collision detection, and injection of bits onto the network.
-layer functions including conversion of the digital data from the Ethernet interface, collision
-detection, and injection of bits onto the network.
+===== Maximum Burst Tolerance =====
-Maximum Burst Tolerance - the largest burst of data that a network device is guaranteed to
+ - the largest burst of data that a network device is guaranteed to
 handle without discarding cells or packets. Bursts of data larger than the maximum burst size
 may be subject to discard.
-MCR (Minimum Cell Rate) - parameter defined by the ATM Forum for ATM traffic manage-
-ment. MCR is defined only for ABR transmissions, and specifies the minimum value for the
+===== MCR (Minimum Cell Rate) =====
-ACR.
+ - parameter defined by the ATM Forum for ATM traffic management. MCR is defined only for ABR transmissions, and specifies the minimum value for the ACR.
-Metasignalling - an ATM Layer Management (LM) process that manages different types of
-signalling and possibly semipermanent virtual channels (VCs), including the assignment,
+===== Metasignalling =====
+ - an ATM Layer Management (LM) process that manages different types of
+signalling and possibly semi-permanent virtual channels (VCs), including the assignment,
 removal, and checking of VCs.
-Metasignalling VCs - the standardized VCs that convey metasignalling information across a
+===== Metasignalling VCs =====
+ - the standardized VCs that convey metasignalling information across a
 User-to-Network Interface (UNI).
-MIB (Management Information Base) - the set of parameters that an SNMP management sta-
-tion can query or set in the SNMP agent of a networked device (e.g., router).
+===== MIB (Management Information Base) =====
-MIC (Media Interface Connector) - the optical fiber connector that joins the fiber to the FDDI
+ - the set of parameters that an SNMP management station can query or set in the SNMP agent of a networked device (e.g., router).
-controller.
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual Glossary - 17
+===== MIC (Media Interface Connector) =====
-Glossary
+ - the optical fiber connector that joins the fiber to the FDDI controller.
-Glossary
-MicroChannel - a proprietary 16- or 32-bit bus developed by IBM for its PS/2 computers’
+===== MicroChannel =====
+ - a proprietary 16- or 32-bit bus developed by IBM for its PS/2 computers’
 internal expansion cards; also offered by others.
-MTU (Maximum Transmission Unit) - the largest unit of data that can be sent over a type of
-physical medium.
+===== MTU (Maximum Transmission Unit) =====
-Multi-homed - a device that has both an ATM and another network connection, typically
+ - the largest unit of data that can be sent over a type of physical medium.
-Ethernet.
-Multiplexing - a function within a layer that interleaves the information from multiple con-
+===== Multi-homed =====
-nections into one connection (see demultiplexing).
+ - a device that has both an ATM and another network connection, typically Ethernet.
-Multipoint Access - user access in which more than one terminal equipment (TE) is sup-
+===== Multiplexing =====
+ - a function within a layer that interleaves the information from multiple connections into one connection (see demultiplexing).
+===== Multipoint Access =====
+ - user access in which more than one terminal equipment (TE) is sup-
 ported by a single network termination.
-Multipoint-to-Point Connection - a Point-to-Multipoint Connection may have zero band-
+===== Multipoint-to-Point Connection =====
+ - a Point-to-Multipoint Connection may have zero band-
 width from the Root Node to the Leaf Nodes, and non-zero return bandwidth from the Leaf
-Nodes to the Root Node. Such a connection is also known as a Multipoint-to-Point Connec-
+Nodes to the Root Node. Such a connection is also known as a Multipoint-to-Point Connection.
-tion.
-Multipoint-to-Multipoint Connection - a collection of associated ATM VC or VP links, and
+===== Multipoint-to-Multipoint Connection =====
-their associated endpoint nodes, with the following properties:
+ - a collection of associated ATM VC or VP links, and their associated endpoint nodes, with the following properties:
 . All N nodes in the connection, called Endpoints, serve as a Root Node in a Point-to-Multi-
 point connection to all of the (N-1) remaining endpoints.
 . Each of the endpoints can send information directly to any other endpoint, but the receiving
-endpoint cannot distinguish which of the endpoints is sending information without addi-
+endpoint cannot distinguish which of the endpoints is sending information without additional (e.g., higher layer) information.
-tional (e.g., higher layer) information.
-Near-End - in a relationship between two devices in a circuit, the near-end device is the one
+===== Near-End =====
+ - in a relationship between two devices in a circuit, the near-end device is the one
 that is local.
-Network Module - ATM port interface cards which may be individually added or removed
+===== Network Module =====
+ - ATM port interface cards which may be individually added or removed
 from any ForeRunner ATM switch to provide a diverse choice of connection alternatives. Each
 network module provides between one and six full-duplex ATM physical connections to the
 ForeRunner switch.
-NMS (Network Management Station) - the system responsible for managing a network or a
+===== NMS (Network Management Station) =====
+ - the system responsible for managing a network or a
 portion of a network. The NMS talks to network management agents, which reside in the
 managed nodes.
-NNI (Network-to-Network Interface or Network Node Interface) - the interface between two
-public network pieces of equipment.
+===== NNI (Network-to-Network Interface or Network Node Interface) =====
-nonvolatile - a term used to describe a data storage device (memory) that retains its contents
+ - the interface between two public network pieces of equipment.
+===== nonvolatile =====
+ - a term used to describe a data storage device (memory) that retains its contents
 when power is lost.
-Glossary - 18
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual
-Glossary
+===== NuBus =====
-NuBus - a high-speed bus used in the Macintosh family of computers, structured so that users
+ - a high-speed bus used in the Macintosh family of computers, structured so that users
 can put a card into any slot on the board without creating conflict over the priority between
-those cards
+those cards.
-OAM (Operation and Maintenance) Cell - a cell that contains ATM LM information. It does
-not form part of the upper layer information transfer.
+===== OAM (Operation and Maintenance) Cell =====
-octet - a grouping of 8 bits; similar, but not identical, to a byte.
+ - a cell that contains ATM LM information. It does not form part of the upper layer information transfer.
-OID (Object Identifier) - the address of a MIB variable.
-OOF (Out-of-Frame) - a signal condition and alarm in which some or all framing bits are lost.
+===== octet =====
-OpenView - Hewlett-Packard’s network management software.
+ - a grouping of 8 bits; similar, but not identical, to a byte.
-OSI (Open Systems Interconnection) - the 7-layer suite of protocols designed by ISO com-
-mittees to be the international standard computer network architecture.
+===== OID (Object Identifier) =====
-OSPF (Open Shortest Path First) Protocol - a routing algorithm for IP that incorporates
+ - the address of a MIB variable.
-least-cost, equal-cost, and load balancing.
-Out-of-Band Management - refers to switch configuration via the serial port or over Ether-
+===== OOF (Out-of-Frame) =====
-net, not ATM.
+ - a signal condition and alarm in which some or all framing bits are lost.
-packet - a group of bits - including information bits and overhead bits - transmitted as a com-
-plete package on a network. Usually smaller than a transmission block.
+===== OpenView =====
+ - Hewlett-Packard’s network management software.
+===== OSI (Open Systems Interconnection) =====
+ - the 7-layer suite of protocols designed by ISO committees to be the international standard computer network architecture.
+===== OSPF (Open Shortest Path First) Protocol =====
+ - a routing algorithm for IP that incorporates least-cost, equal-cost, and load balancing.
+Out-of-Band Management - refers to switch configuration via the serial port or over Ethernet, not ATM.
+===== packet =====
+ - a group of bits - including information bits and overhead bits - transmitted as a complete package on a network. Usually smaller than a transmission block.
 Packet Port - a port on the CellPath 300 that transmits and receives packet traffic.
 Packet Switching - a communications paradigm in which packets (messages) are individu-
@@ Line 1066: / Line 1300: @@
 VT (Virtual Tributary) - a structure used to carry payloads such as DS1s that run at signifi-
 cantly lower rates than STS-1s.
-WAN (Wide-Area Network) - a network that covers a large geographic area.
-ForeRunner HE/200E/LE ATM Adapters for the PC User’s Manual Glossary - 27
+===== WAN (Wide-Area Network) =====
-Glossary
+ - a network that covers a large geographic area.
-Glossary
-Warm Start Trap - a CellPath 300 SNMP trap that indicates that SNMP alarm messages or
+===== Warm Start Trap =====
-agents have been enabled.
+ - a CellPath 300 SNMP trap that indicates that SNMP alarm messages or agents have been enabled.
-Yellow Alarm - an alarm that occurs on a device when the signal from the device is not
-received at the far-end.
+===== Yellow Alarm =====
-X.21 - ITU-T standard for serial communications over synchronous digital lines. The X.21 pro-
+ - an alarm that occurs on a device when the signal from the device is not received at the far-end.
-tocol is used primarily in Europe and Japan.
-X.25 - ITU-T standard that defines how connections between DTE and DCE are maintained
+===== X.21 =====
+ - ITU-T standard for serial communications over synchronous digital lines. The X.21 protocol is used primarily in Europe and Japan.
+===== X.25 =====
+ - ITU-T standard that defines how connections between DTE and DCE are maintained
 for remote terminal access and computer communications in PDNs. X.25 specifies LAPB, a
-data link protocol, and PLP, a network layer protocol. Frame Relay has, to some degree, super-
+data link protocol, and PLP, a network layer protocol. Frame Relay has, to some degree, superseded X.25. See also Frame Relay, LAPB, and PLP.
-seded X.25. See also Frame Relay, LAPB, and PLP.
 ----